Simpson rafter hangers7/6/2023 I found it easier to insert the rafter if I attached the rafter hanger with two screws at one side, while leaving out the two screws at the other side until after the rafter was slipped into place. Need to find party rentals in Simpson, West Virginia Maybe youre planning a party for 25 people, but only have enough chairs for 10. I used the recommended Simpson Strong-Tie screws instead of nails. The LRUZ offers an economic alternative for those applications requiring a sloped hanger for rafter-to-ridge connections. The "Patio Cover" picture shows a view under the header between two support posts, and the purlin strips are visible overhead. The picture titled "Rafter Hanger at Eave" shows that the bottom of the rafter and lower portion of the rafter hanger are actually about an inch below the fascia strip.Īlso to increase head room, the purlin strips (2 x 4 lumber) were cut to fit between the rafters, rather than run across the top of the rafters. Note that the attachment holes are high up on the hanger, which permitted attachment to a fascia that was narrower than the rafter without compromising strength. Simpson LRU26Z Light Rafter U Hanger - Slopeable 2圆 - Zmax Finish Skip to product information Shop more LRUZ Rafter Hangers Browse SKU: LRU26Z Simpson LRU26Z Light Rafter U Hanger - Slopeable 2圆 - Zmax Finish 5.38 Quantity Add to cart Ships Mar 20 when you order now. Simpson Strong-Tie LUS ZMAX Galvanized Face-Mount Joist Hanger for 2x10 Nominal Lumber Simpson Strong-Tie LRUZ ZMAX Galvanized Slopeable Light Rafter U Joist Hanger for 2 in. This versatile hanger is field adjustable for skewing up to 45° either left or right and features an innovative hinged swivel seat to adjust for up to a 45° slope. The picture titled "Rafter Hanger at Header" shows that the roof sheets are flush with the top of the rafters and with the top of the header. The Simpson Strong-Tie LSSR210Z Slopeable and Skewable Rafter Hanger allows you to install a nominal 2 x 10 rafter with either a plumb cut or miter cut that has been tacked in place. Usually, rafters sit on top of a support header, but I butted the rafters into the header with the top of the rafter flush with the top of the header to increase head room underneath. Joist fasteners must be installed at an angle through the rafter or joist into the header to achieve the table loads.To address the issue of limited head room, I used the ZMax Rafter Hanger at both ends of the rafters for a patio cover. The patent-pending LSSR light slopeable/skewable rafter hanger is the next generation of a field-adjustable rafter hanger.Can be installed using nails or Strong-Drive® SD Connector screws Simpson Strong-Tie LRUZ ZMAX Galvanized Slopeable Light Rafter U Hanger for 2x8 (Pack of 25) Visit the Simpson Strong-Tie Store 22 ratings -9 17900 List Price: 196.For added versatility the fasteners are placed higher on the hanger allowing the bottom of the rafter to hang below the ridge beam (see "Max.For slopes greater than 45° up to 49° (14:12), allowable loads are 0.85 of table loads Accommodates roof pitches from 0:12 to 14:12 LRUZ ZMAX Galvanized Slopeable Light Rafter U Joist Hanger for 2 in.The open design and ability to field-adjust the slope makes the LRUZ ideal for both retrofit or new applications.The LRUZ offers comparable or better load capacity to other rafter hangers at a reduced cost while using fewer fasteners.The Strong-Tie LRU212Z reinforcing angle features a G185 ZMAX galvanized finish for added corrosion resistance and requires the use of hot-dip galvanized fasteners which meet the specifications of ASTM A153. The field-adjustable seat helps improve job efficiency by eliminating mismatched angles in the field and lead times associated with special orders. For additional information, see Fastener Types and Sizes Specified for Simpson Strong-Tie Connectors. Fasteners: Nail dimensions in the table are listed diameter by length. LSU3510-2, LSU4.12, LSU4.28, and LSU5.12 skew options must be factory-ordered. The innovative design of the LSSR Slopeable & Skewable Rafter Hanger allows it to adjust for skew up to 45° and features an innovative hinged swivel seat to adjust for up to a 45° slope on site, eliminating the need for preskewed/sloped or customorder hangers. Used with solid-sawn rafters, the LRUZ’s unique design enables the hanger to be installed either before or after the rafter is in place. Minimum 11' joist height for LSU3510-2, LSU4.12, LSU4.28 and LSU5.12. Simpson Strong-Tie LRU light rafter U hangers are an economic alternative for applications requiring a sloped hanger for rafter-to-ridge connections.
0 Comments
Leave a Reply. |